First off, that’s not the industry standard. At least, not for any industry I’m familiar with. ARM-based MCUs like the Freescale Kinetis series or ST. M16C. From Wikipedia, the free encyclopedia. Redirect page. Jump to navigation Jump to search. Redirect to: Renesas Electronics#M16C microcontrollers. R5FMDFA#U0 from RENESAS >> Specification: Microcontroller, M16C Family M16C 60 Series Microcontrollers, 16bit, 25 MHz, KB, 31 KB.
|Published (Last):||20 October 2017|
|PDF File Size:||8.90 Mb|
|ePub File Size:||12.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
I know it’s the industry standard but what would it add to my simple project? Do I need a bootloader? I’m thinking maybe this is a type of spam. Start with something that you can understand using your existing level of knowledge and skill. So, to answer your question, I really can’t think of a reason why you should use a Renesas M16C. Please microcnotroller the help center to learn how to ask good questions.
One option is to use a 1-wire “silicon serial number” chip DS Who would’ve thought all that work I did on them 10 years ago would finally pay off I have to apologize because I have found the answer just a few posts below after posting this.
The simliest way would be to save a variable in every MCU i think. At least, not for any industry I’m familiar with.
To read a string of bytes from a pre-determined memory address FFFC0 in this exampleuse code like this: All M16C devices have a boot loader built-in. What are the advantages of working with the Renesas M16C microcontroller?
Another issue is that: First microcontrolller, that’s not the industry standard. There isn’t really such a thing as “the industry standard microcontroller” except possibly in some manufacturers’ marketing departments as something they like to tell themselves. How can I achieve that?
Microcontrollers unique ID ?
Ok, now its clear. Nothing is really superior in general, it’s more so what fits your project. If this question can be reworded to fit the rules in the help centerplease edit the question. Home Questions Tags Users Unanswered. The solution with external chips is to complicated i think. Each is guaranteed to have a unique bit serial number, and you only need to use up one pin of the MCU to interface with it.
I already downloaded FDT. In order to identify a device I would like to read out a uniqie ID from the mfcgp.
Another micricontroller is to have your flash programmer insert a unique serial number at a fixed location in each image it saves, but if you’re doing remote updates that might wipe out the number unless you’re careful to not reprogram that flash block.
Many good questions generate some degree of opinion based on expert experience, but answers to this question will tend to be almost entirely based on opinions, rather than facts, references, or specific expertise.
Would it be ok to work with an Arduino for instance? What if I use: Usually, you go with a component that meets the need and nothing more.
M16C TinyBrick | Elektor Magazine
Use something popular in the community. If your application provides a UART interface on UART1 of the device, and if the application has some jumper or so to set the device to flash programming you don’t need additional hardware for programming M Meaning, we can’t say what is better for you, that depends on your project.
Not to forget good readable datasheets. This is provided as Visual Studio 6 source on the Renesas hompeage http: FDT does not support such an old device as M There’s an industry standard microcontroller!!?? I personally m16 to add toolchain support on Linux as that is a very comfortable platform for developing your own software and tools in my opinion.
If you can’t understand it from the website and its datasheet, then it’s unlikely that you are going to be successful using it. I still microcontriller some questions: There are many more MCU lines that are used quite a lot. I also have some information on serially programming m32c’s here: Do I have to write a ID in memory first or does such a number already exist? The Renesas M16C is not an ‘industry standard’ for me. What are the superior features?
There are a slew of easy-to-use MCU development boards out there to remedy this. So we can’t help you.
In any case I voted to close as too opinion based.