Automotive

ASTM F2248 PDF

September 17, 2020

¼” screws at four jamb corners – screws bending corners screws bending. – tearing in frame wall at connections pushing limits of ASTM F □ Minimal. ASTM F Standard Practice for Specifying an Equivalent 3-Second Duration Design Loading for Blast Resistant Glazing Fabricated with. Mullion/Frame Design – Allowable Stress Design. ▫ Design Load = Equivalent 3 second design load ASTM F ▫ Info Required –. ▫ 1) Level of Protection.

Author: Akinotaxe Magal
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Education
Published (Last): 24 April 2010
Pages: 66
PDF File Size: 16.81 Mb
ePub File Size: 19.42 Mb
ISBN: 220-9-45928-801-8
Downloads: 72866
Price: Free* [*Free Regsitration Required]
Uploader: Kazikora

The standard explain different methods to check the thickness f2248 type of blast resistant glazing fabricated with laminated glass to glaze a fenestration. ASTM F is a standard practice for specifying an equivalent 3-Second Duration design loading for blast resistant glazing fabricated with laminated glass.

ASTM F 2248

The width of silicone f2428 glazing tape is referred to as bite and is shown and discussed in Guide C The fasteners that attach the framing system that zstm the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least: The system shall be designed to ensure that the glazing fails prior to the framing system that supports the glazing and its attachment to the structural framing system.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and xstm the applicability of regulatory limitations prior to use. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least: Work Item s – proposed revisions of this standard.

Blast testing has shown that use of fully tempered glass plies, when fractured during a blast event, have poorer post blast performance than annealled or heat strengthened glass plies. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  EL ASESINATO DE MARIE ROGET PDF

As a minimum, insulating glass shall use laminated glass for the inboard protected side lite. Use of the annealed or heat strengthened glass plies will also f22248 the amount of load transferred into the structure. Historical Version s – view previous versions of standard. Glass plies used to construct laminated glass are recommended to be either annealed or heat strengthened glass. As a minimum, insulating glass shall use laminated glass for the inboard protected side lite.

From Wikipedia, the free encyclopedia. The system shall be designed to ensure that the glazing fails prior to the framing system that supports the glazing and its attachment to the structural framing system. The standard explain different methods to check the thickness and type of blast resistant glazing fabricated with laminated glass to glaze a fenestration The main keywords to present this standard are air blast pressure, blast resistant glazing, explosion, insulating glass, and laminated glass.

ASTM F – Wikipedia

atsm The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least:. Link to Active This link will always route to the current Active version of the standard. Laminated glass fabricated with fully tempered glass plies has f2284 tendency to leave the supporting glazing system frame after fracture whereas laminated glass fabricated with annealed or heat strengthened glass plies will remain in the frame and absorb remaining load through tensile membrane behavior.

Use of the annealed or heat strengthened glass plies will also reduce the amount of load transferred into the structure. This page was last edited on 28 Marchat ASTM International which was funded inis an international standards developing organization that develops and publishes standards for a wide range of materials, products, systems, and services. Work Item s – proposed revisions of this standard. The width of silicone or glazing tape is referred to as bite and is shown and discussed in Guide C Retrieved from ” https: Laminated glass fabricated with fully tempered glass plies has a tendency to leave the supporting glazing system frame after fracture whereas laminated glass fabricated with annealed or heat strengthened glass plies will remain in the frame and absorb remaining load through tensile membrane behavior.

  BRISS CROP PDF

The width of glazing tape shall be at least equal to two times but not more than four times the thickness designation of the glass to which it adheres. Active view current version of standard. By using this site, you agree to the Terms of Use and Privacy Policy. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Values given in parentheses are for information only. Views Read Edit View history. This f2428 was published by ASTM F14 which is a committee specializes about on systems products and services.

The asttm of glazing tape shall be at least equal to two times but not more than four times the thickness designation of the glass to which it adheres. The main keywords to present this standard are air blast pressure, blast resistant glazing, explosion, insulating glass, and laminated glass.

The fasteners that attach the framing system that supports the glazing to the structural framing system shall be designed to resist a uniform load acting on the blast resistant glazing that has a magnitude of at least:. Link to Active This link will always route adtm the current Active version of the standard.